Magnetek Enrange CAN-6 Technical Information

CAN-6 Enrange CAN-6 Radio Receiver September 2011 Part Number: 198-00244-1000-R1 ©Copyright 2011 Magnetek Material Handling

Enrange CAN-6 Instruction Manual September 2011 Page 9 of 24 Figure 02: CAN-6 with external antenna (red) Figure 03: CAN-6 (900 MHz vers

Enrange CAN-6 Instruction Manual September 2011 Page 10 of 24 3.3 INSTALLATION 1. Determine the location of your antenna from Figures 01-03 (the ante

Enrange CAN-6 Instruction Manual September 2011 Page 11 of 24 3.5 PIN OUT DIAGRAM AND DEFINITIONS Figure 06: Pin out diagram

Enrange CAN-6 Instruction Manual September 2011 Page 12 of 24 +Vbattery (Left Pin 7 and Right Pin 1) The CAN-6 is designed to work in any 12–24VDC nom

Enrange CAN-6 Instruction Manual September 2011 Page 13 of 24 3.6 CAN-6 RECEIVER BLOCK DIAGRAM NOTE: Connections are labeled by which side the connec

Enrange CAN-6 Instruction Manual September 2011 Page 14 of 24 4.0 CONFIGURING THE CAN-6 The CAN-6 receiver will be pre-configured at the factory in m

Enrange CAN-6 Instruction Manual September 2011 Page 15 of 24 4.3 RECEIVER CHANNEL CONFIGURATION SETTINGS (DIP SWITCH BANK 2) The channel can be set

Enrange CAN-6 Instruction Manual September 2011 Page 16 of 24 4.3.1 Channel Dip Switch Settings for 900MHz Part 15

Enrange CAN-6 Instruction Manual September 2011 Page 17 of 24 4.3.2 Channel Dip Switch Settings for 433MHz Part 15

Enrange CAN-6 Instruction Manual September 2011 Page 18 of 24 4.3.3 Channel Dip Switch Settings for 2.4GHz @ 50mW and 125mW

Enrange CAN-6 Instruction Manual September 2011 Page 1 of 24 Your New Radio Receiver Thank you for your purchase of Magnetek’s EnrangeTM CAN-6 Radio C

Enrange CAN-6 Instruction Manual September 2011 Page 19 of 24 4.4 FCC STATEMENTS Compliance Statement (Part 15.19) This device complies with Part 15

Enrange CAN-6 Instruction Manual September 2011 Page 20 of 24 5.0 NORMAL OPERATION During normal operation the CAN-6 receiver will receive commands f

Enrange CAN-6 Instruction Manual September 2011 Page 21 of 24 5.3.2 Signal Strength/Error Code LED (Bottom LED on CAN-6 Faceplate) Solid Green = Go

Enrange CAN-6 Instruction Manual September 2011 Page 22 of 24 6.0 TROUBLESHOOTING 6.1 TROUBLESHOOTING TABLE Problems Possible Reasons Suggestions R

Enrange CAN-6 Instruction Manual September 2011 Page 23 of 24 CAN messages transmitted by the receiver are not being received Incorrect source address

Enrange CAN-6 Instruction Manual September 2011 Page 24 of 24 6.2 ASSEMBLY AND REPLACEMENT PARTS If your receiver ever needs repair, we always recomm

Enrange CAN-6 Instruction Manual September 2011 Page 2 of 24 TABLE OF CONTENTS 1.0 INTRODUCTION ...

Enrange CAN-6 Instruction Manual September 2011 Page 3 of 24 1.0 INTRODUCTION Thank you for your purchase of Magnetek’s Enrange® brand CAN-6 Radio Wir

Enrange CAN-6 Instruction Manual September 2011 Page 4 of 24 1.2 WARNINGS and CAUTIONS Throughout this document WARNING and CAUTION statements ha

Enrange CAN-6 Instruction Manual September 2011 Page 5 of 24 2.0 CRITICAL INSTALLATION CONSIDERATIONS WARNING PRIOR TO INSTALLATION AND OPERATION OF

Enrange CAN-6 Instruction Manual September 2011 Page 6 of 24 2.3 SAFETY INFORMATION & RECOMMENDED TRAINING FOR RADIO CONTROLLED EQUIPMENT OPERATO

Enrange CAN-6 Instruction Manual September 2011 Page 7 of 24 operate a crane, hoist or lifting device if the chain or wire rope is not seated proper

Enrange CAN-6 Instruction Manual September 2011 Page 8 of 24 3.0 CAN-6 RECEIVER INSTALLATION WARNING BEFORE OPERATING THE RECEIVER, FAMILIARIZE YOUR